Boosting Auto Industry Efficiency with High-Performance Walking Beam Furnaces
Boosting Auto Industry Efficiency with Walking Beam Furnaces - NUTEC Bickley
March 24, 2025
3 minutes
NUTEC Bickley’s walking beam furnaces optimize heat treatment for truck beams, featuring advanced combustion, insulation, and energy efficiency.
Arturo Arechavaleta – VP Metal Furnaces
NUTEC Bickley is currently installing a truck beam heat treat line incorporating two large walking-beam furnaces – one for austenitizing and the other for tempering. The contract for these specialist furnaces was won against strong international competition and was awarded by one of the leading global auto structural component designers and manufacturers, boasting numerous plants and thousands of employees. Confirmation of NUTEC Bickley’s ability to design and manufacture superior systems is that this is the third such order from this important customer.
High Performance Austenizing Furnace for Steel Beams
The austenitizing furnace is a continuous unit, capable of treating 60 beams (roughly equivalent to 17 tons of steel) per hour. It has an operating temperature of 910°C (1670°F), and a maximum temperature of 1100°C (2010°F). There are 10 automatic control zones, designed to promote temperature uniformity.
The truck beams are 33cm (13in) wide, 11.5cm (4.5in) high, 15m (49ft) long, and each weighs around 285kg (625lb). A closely controlled environment is necessary in order to induce the required change to the steel beams’ crystal structure.
There are 29 high-velocity burners, sited above the load. These top brand burners are one of the most used and respected of their type in the combustion industry. Offering low NOx emissions, they feature stable high excess air and excess fuel operation, direct spark ignition, integral air and gas meters, sturdy cast construction and flame rod ionization. The burner configuration creates gas recirculation and allows uniform heating of the load and better heat transfer to the product through radiation mechanisms and convection.
The furnace employs NUTEC Bickley’s IMPS™ combustion system that uses a predetermined pulse sequence to control individual burners or burner groups based on the heat requirements of each control zone. IMPS provides multiple benefits, including energy savings, enhanced process control, optimal kinetic energy utilization from burners, improved temperature uniformity without excess air, a high turndown ratio, flexible rezoning through software, high gas recirculation rates, better energy transfer to the product, and reduced NOx emissions.
This austenitizing furnace is designed with an area close to the entrance where the beams are preheated before moving forward. Heating is then ramped up to 910°C in a maximum time of 27 minutes.
A high-capacity austenitizing furnace treating 60 beams per hour at 910°C. Features 29 high-velocity burners and IMPS™ combustion for efficiency.
The tempering furnace – which is also capable of heat treating beams at a rate of 60 pieces per hour – has an operating temperature of 490°C (915°F) and a maximum temperature of 600°C (1110°F). There are six automatic control zones and the heating method for tempering is via air circulation with a vertical flow pattern, ceiling to floor. This is achieved with six centrifugal fans, one for each combustion chamber. The combination of multiple chambers and control zones with recirculation fans optimizes convective heating inside the furnace.
Medium-speed burners are employed in this furnace, sited above the load, with one for each control zone.
As with the austenitizing furnace there is a preheat section, with heating being ramped from room temperature up to 490°C in a maximum time of 27 minutes.
A precision-engineered annealing furnace with six control zones and vertical air circulation, ensuring even heating and optimal steel properties.
Thermal Efficiency and Advanced Insulation in Walking Beam Furnaces
Both of these furnaces benefit from advanced insulation based on the patented Jointless® ceramic fiber system that allows faster heating and cooling and reduces heat storage. Using MacroModules, this insulation is 8in (20cm) thick in the combustion zones. Optimal thermal efficiency has also been guaranteed with an improved design of the door frame and canopy for both access and exit doors. Both furnaces are fully NFPA 86 compliant.
Equipped with Jointless® ceramic fiber insulation and optimized doors, this furnace reduces heat loss, speeds up cycles, and enhances efficiency.
For all further information, please contact:
Arturo Arechavaleta – VP Metal Furnaces
NUTEC Bickley
Carr Saltillo–Monterrey 100 (Km 62.5)
66359 Santa Catarina NL, Mexico
Tel: +52 81 8254 0633
E-mail: arturoarechavaleta@nutec.com
This is Nutec Bickley
Providing Thermal Equipment Solutions that go beyond expectations
We serve multiple industries through the design, building and installation of combustion systems, thermal insulation and highly specialized industrial furnaces, kilns and ovens. We are focused on understanding our customers’ needs and supplying the best equipment at the most competitive price.
In a major, high-value project – the second at this particular plant in Mexico – NUTEC Bickley will supply a 125m-long tunnel kiln to one of the world’s leading advanced ceramics manufacturers.
Do you want advice to select the ideal furnace or spare part for your project?
We offer specialized technical support and advice to ensure that you choose the solution that best suits your needs. Fill out this form or contact us to talk to us now.